1. Microtronik Autohex II and Hexprog forum
  2. Autohex II BMW
  3. BMW Locksmith
  4. E46 Cluster cloning
pungo1212
2022-09-12T00:40:22Z
Hi. So far I have used the Hextag to clone a couple of CAS modules but I don't use it too much because of the type of work I get. Now I have an E46 the the cluster is taking down the K-bus, so I want to install a used one. I can't find any microtronik videos that show how to do it. Can it be done without removing the chip? If I have to remove it, how do I connect to Hexprog? Thank you. I apologize but I haven;t used it very much and finding any instructions on this topic is not easy.Thank you for your help.
Sponsor

Start ECU Repairing, ECU Cloning, and Chip Tuning today, all from an incredible price of just USD 385.00.

No annual fees, no extra charges: You pay only when you have a job.

Visit Hexprog II page

PDXAutoworks
2022-09-12T16:50:49Z
Disassemble the cluster and remove the 35080 eeprom chip. Use the provided eeprom adaptor and read the data from the chip. Edit the data, write back and solder the chip back on.
BMW File Service
VAG Immo Data Transfer
pungo1212
2022-09-14T02:23:28Z
What Hex edit program did you use for the VIN edit? I am trying to figure out the best way. I read it and changed miles, but I still need to do VIN. Thank you very much.
pungo1212
2022-09-14T02:46:39Z
OK. I used Hex Editor and was able to open my file. Now how can I tell which is the VIN and how can I change it to new vin?
Thank you again.
I was trying to attach the file here but it won't let me.
Autohex_II_BMW
2022-09-14T09:09:17Z
have to locate the vin from eeprom file and edit that manually, please check if eeprom vin is encrypted or not.
PDXAutoworks
2022-09-14T14:06:43Z
Put the file here and I can help you with the VIN.
BMW File Service
VAG Immo Data Transfer
pungo1212
2022-10-08T00:42:31Z
It is encrypted. What can I do?
pungo1212
2022-10-08T00:43:47Z
I tried to put it here but it won't let me because the file is too big, Also it's encrypted. What should I do?
PDXAutoworks
2022-10-09T18:09:47Z
Compress the file and attach it here as a zip file
BMW File Service
VAG Immo Data Transfer
pungo1212
2022-10-10T15:14:03Z
 M35080_2022_09_12_21_24_11.zip You have insufficient rights to see the content.
pungo1212
2022-10-10T15:18:55Z
I just posted the file compressed. I hope I did it right. If someone can help I would be grateful, or if anyone can recommend a company. I tried Precision ECU but they don't respond and after reading reviews on the internet I am afraid to waste more money. If None here can help I will have to try swapping EEPROM but I don't know if mine is actually the problem.
PDXAutoworks
2022-10-17T04:32:46Z
What VIN and mileage do you need put inside the 35080?
BMW File Service
VAG Immo Data Transfer
pungo1212
2022-10-17T20:17:08Z
Mileage is 115234. Vin is WBAEV53455KM42462.

THANK YOU VERY MUCH.
PDXAutoworks
2022-10-18T01:25:12Z
here you go

 M35080_2022_09_12_21_24_11_modified.zip You have insufficient rights to see the content.
BMW File Service
VAG Immo Data Transfer
pungo1212
2022-10-18T19:41:08Z
Originally Posted by: PDXAutoworks 

here you go

 M35080_2022_09_12_21_24_11_modified.zip You have insufficient rights to see the content.



Thank you again. I am going to try now. I will let you know.
pungo1212
2022-10-18T20:02:06Z
Now, being this is a zip file, do I have to do anything before I can see load it to HexProg?
PDXAutoworks
2022-10-18T21:04:37Z
Unzip the file and then write it using hexprog. The chip must be taken off of the circuit board in order to successfully write.
BMW File Service
VAG Immo Data Transfer
pungo1212
2022-10-23T14:47:05Z
Originally Posted by: PDXAutoworks 

Unzip the file and then write it using hexprog. The chip must be taken off of the circuit board in order to successfully write.




I was able to do everything but when I installed it, a CodE message comes on and not of the gauges or odometer work. My original problem with K bus down got fixed, though. I was able to erase codes from DSC but I can't get KOMBI to work. If I try to code it, it says that Vehicle Order in Immobilizer is different from KOMBI. Any ideas? Thanks in advance.
By the way same thing happens if I use the original EEPROM with the donor cluster.
Similar Topics
Users browsing this topic
    1. Microtronik Autohex II and Hexprog forum
    2. Autohex II BMW
    3. BMW Locksmith
    4. E46 Cluster cloning