fukui
  •  fukui
  • 54.4% (Neutral)
  • Newbie Topic Starter
2021-03-11T13:41:39Z
Hi all ,

has anyone experienced "no response from ECU" while cloning / reading 271 DE ecu in boot mode between version 1.0.28 & 1.0.29 ?

1) i tried reading 5 ecus but failed
2) checked all wiring and pins with ohm meter ( all good )
3) ecu has communication while reading using diagnostic machine
4) used a friend's device ( other brand ) to clone successfully ( using 2 among the 5 ecus i tested with hextag )
5) cloning other ecus in factory mode is fine with my hextag

feel free to share any past experiences /solutions

many thanks
Sponsor

Start ECU Repairing, ECU Cloning, and Chip Tuning today, all from an incredible price of just USD 385.00.

No annual fees, no extra charges: You pay only when you have a job.

Visit Hexprog II page

Alekznbk
2021-03-12T16:07:07Z
Originally Posted by: fukui 

Hi all ,

has anyone experienced "no response from ECU" while cloning / reading 271 DE ecu in boot mode between version 1.0.28 & 1.0.29 ?

1) i tried reading 5 ecus but failed
2) checked all wiring and pins with ohm meter ( all good )
3) ecu has communication while reading using diagnostic machine
4) used a friend's device ( other brand ) to clone successfully ( using 2 among the 5 ecus i tested with hextag )
5) cloning other ecus in factory mode is fine with my hextag

feel free to share any past experiences /solutions

many thanks



did u update the hexprog?

fukui
  •  fukui
  • 54.4% (Neutral)
  • Newbie Topic Starter
2021-03-13T02:38:04Z
Originally Posted by: Alekznbk 

Originally Posted by: fukui 

Hi all ,

has anyone experienced "no response from ECU" while cloning / reading 271 DE ecu in boot mode between version 1.0.28 & 1.0.29 ?

1) i tried reading 5 ecus but failed
2) checked all wiring and pins with ohm meter ( all good )
3) ecu has communication while reading using diagnostic machine
4) used a friend's device ( other brand ) to clone successfully ( using 2 among the 5 ecus i tested with hextag )
5) cloning other ecus in factory mode is fine with my hextag

feel free to share any past experiences /solutions

many thanks



did u update the hexprog?



yup i've updated it to 1.0.30 and tried again today but still no luck at the moment
mbenztech
2021-03-13T07:29:12Z
Same thing happened to me today. I checked everything possible but not reading. I was so busy that I forgot to send a message to tech support. I think it gave error ref-972...... I think. The wiring shows two boot pins connections and one signal connection. I have also updated to latest update.
Autohex_II_BMW
2021-03-13T10:37:14Z
Originally Posted by: fukui 

Originally Posted by: Alekznbk 

Originally Posted by: fukui 

Hi all ,

has anyone experienced "no response from ECU" while cloning / reading 271 DE ecu in boot mode between version 1.0.28 & 1.0.29 ?

1) i tried reading 5 ecus but failed
2) checked all wiring and pins with ohm meter ( all good )
3) ecu has communication while reading using diagnostic machine
4) used a friend's device ( other brand ) to clone successfully ( using 2 among the 5 ecus i tested with hextag )
5) cloning other ecus in factory mode is fine with my hextag

feel free to share any past experiences /solutions

many thanks



did u update the hexprog?



yup i've updated it to 1.0.30 and tried again today but still no luck at the moment


we need more information in this case, we recommend you to contact via skype or WhatsApp on below details for more convenience.
Skype: microtronik@outlook.com
WhatsApp: +971555827622


fukui
  •  fukui
  • 54.4% (Neutral)
  • Newbie Topic Starter
2021-03-14T09:43:30Z
Originally Posted by: mbenztech 

Same thing happened to me today. I checked everything possible but not reading. I was so busy that I forgot to send a message to tech support. I think it gave error ref-972...... I think. The wiring shows two boot pins connections and one signal connection. I have also updated to latest update.



i have contacted them through skype .

multiple ecus .

bosch tricore
continental tricore
mpc

same ecu works in factory mode but not boot mode
fukui
  •  fukui
  • 54.4% (Neutral)
  • Newbie Topic Starter
2021-03-14T10:42:59Z
Originally Posted by: Autohex_II_BMW 

Originally Posted by: fukui 

Originally Posted by: Alekznbk 

Originally Posted by: fukui 

Hi all ,

has anyone experienced "no response from ECU" while cloning / reading 271 DE ecu in boot mode between version 1.0.28 & 1.0.29 ?

1) i tried reading 5 ecus but failed
2) checked all wiring and pins with ohm meter ( all good )
3) ecu has communication while reading using diagnostic machine
4) used a friend's device ( other brand ) to clone successfully ( using 2 among the 5 ecus i tested with hextag )
5) cloning other ecus in factory mode is fine with my hextag

feel free to share any past experiences /solutions

many thanks



did u update the hexprog?



yup i've updated it to 1.0.30 and tried again today but still no luck at the moment


we need more information in this case, we recommend you to contact via skype or WhatsApp on below details for more convenience.
Skype: microtronik@outlook.com
WhatsApp: +971555827622




I have already updated the support team through skype .

hmmmm3
2023-08-01T19:59:47Z
What was the solution? I’m having a similar problem.
Autohex_II_BMW
2023-08-02T07:36:47Z
Originally Posted by: hmmmm3 

What was the solution? I’m having a similar problem.



If you have 972 error in boot mode , then it must be some error with wiring, some ecus need multiple boot and signal. So please make sure boot and signal wires are well connected on ECU Pcb.